氣泡袋的使用好壞可以看出來氣泡袋的生產工藝是怎樣的，因此我們也可以看出來質量好的氣泡袋生產工藝是非常不錯的，因此了解一下氣泡袋的生產工藝是非常重要的，小編給大家做了一些有方面的整理，在下文給大家做個分享。

The use of bubble bag can see how the production process of bubble bag is. Therefore, we can also see that the production process of bubble bag with good quality is very good. Therefore, it is very important to understand the production process of bubble bag. I made some arrangement for you, and I would like to share it with you.

濟南氣泡袋

Jinan bubble bag

1：氣泡袋的模具制作及加工：根據要求或樣品規格，首先制作好吸塑模具，一般條件下，都是利用石膏制作吸塑包裝模具，但也有用木雕及金屬雕刻的產品作模具，石膏模具制作好后，先讓其自然干燥完全或是烘干，然后根據產品表面凸凹具體情況，用1-2毫米鉆花在不影響產品包裝模樣的低凹處鉆許多小孔，如果是包裝盒之類產品，還得在四周邊上鉆一些小孔，以便吸塑生產時，能將空氣抽出，模具鉆好孔后，還得將石膏模具進行加硬處理，加硬處理方法是用濃明礬飽和液浸泡后晾干。

1: Bubble bag mold making and processing: according to the requirements or sample specifications, first make a good blister mold, under general conditions, the use of gypsum to make blister packaging mold, but also use wood carving and metal carving products as the mold, after the gypsum mold is made, first let it dry completely or dry, and then according to the specific situation of the product surface convex concave, use 1-2 mm drill flower Many small holes should be drilled in the concave places that do not affect the product packaging pattern. If it is a packaging box or other products, some small holes should be drilled around the four sides so that the air can be drawn out during the blister production. After the mold is drilled, the gypsum mold must be hardened. The hardening treatment method is to soak in concentrated alum saturated solution and dry it in the air.

2：模具處理干燥完全后，將模具裝入真空室上層鐵板上，然后根據模具大小，將塑料片載成適用規格尺寸，然后將此片材放入加熱木柜內，使其完全固定好，再將木柜連同塑料片材置恒溫爐上進行軟化處理。

2: After the mold is completely dried, the mold is put into the upper iron plate of the vacuum chamber, and then the plastic sheet is loaded into the applicable size according to the size of the mold, and then the sheet is put into the heating wood cabinet to make it completely fixed, and then the wood cabinet and the plastic sheet are placed on the constant temperature furnace for softening treatment.

3：將軟化處理好的塑料片連同木柜，置于真空室中，開動吸氣開關，將真空室內空氣吸抽干凈，待塑料片冷卻后，即得到與氣泡袋模具相同的凹型包裝或工藝模具。

3: Put the softened plastic sheet together with the wooden cabinet in the vacuum chamber. Turn on the suction switch to suck the air in the vacuum chamber. After the plastic sheet is cooled, the concave packaging or process mould which is the same as the bubble bag mold can be obtained.

4：吸塑包裝整理;將生產出來的產品進行修邊整理即為成品產品，再經包裝后即可出售。

4: Blister packing and finishing; trimming and finishing the products are finished products, which can be sold after packaging.

這是氣泡袋的生產工藝了!經過這樣處理的氣泡袋使用起來是非常不錯的，而且我們也可以了解到其中的優勢，如果有消費者需要購買OPP袋,氣泡袋這些產品的話，可以直接電話聯系我們的哦!

This is the production process of bubble bag! After such treatment, the bubble bag is very good to use, and we can also understand its advantages. If consumers need to buy OPP Bags, bubble bags and other products, they can contact us directly by telephone!
關鍵詞：濟南氣泡袋